How to quickly set up a tp link modem router. Setting up an Internet connection for a TP-Link router. Setting up an L2TP connection

1. By default, login is admin, password is admin.
2. Courier-setters must change the password in the settings to the Serial Number indicated on the box (S/N). When reconfiguring, it is also recommended to use S/N as a password for the router and wi-fi ( serial number).
3. Resetting the router settings is done by pressing and holding the Reset button on the back panel of the router for 10 seconds.

In order to get to the router’s web interface, you need to open your Internet browser and type http://192.168.1.1, User Name in the address bar admin, Password – admin(provided that the router has factory settings and its IP has not changed).

Change the factory password.

For security reasons, it is recommended to change the factory password.
Default: Login admin, password admin.
In the router interface, you need to go to the tab System Tools and choose Password.
In the field Old User Name enter admin, Old Password enter admin.
Into the fields New User Name, New Password, Confirm New Password enter a new login (you can leave the same “admin”), and also New Password and its repetition accordingly.

Then click the button Save.

SettingsWiFion the router.

In the router interface, you need to select the tab on the left “ Wireless ", in the list that opens, select " Wireless Serrings».

We set the parameters as follows:

1. Field " SSID": enter the name of the wireless network.
2. Region: Russia
3. Chanel: Auto
4. Mode: 11bgn mixed
5. Channel Width: Automatic
6. Max Tx Rate: 300Mbps
7. Click the button below “ Save»

On the left menu select “ Wireless", then " Wireless Security"and set the parameters:

1. Set the point to WPA-PSK/WPA2-PSK
2.Version: WPA2-PSK
3. Encryption: Automatic
4. PSK Password: you must enter any set of numbers ranging from 8 to 63. They also need to be remembered so that you can specify them when connecting to the network. It is recommended to use the device serial number as a key (indicated on the box, in the form S/N########).
5. Click the button below “ Save»

Setting up an Internet connection.

SettingsPPPoEconnections.

1. Select the menu on the left Network, further MAC Clone
2. Click Clone MAC address, further Save (for more details see in section "MAC Cloning addresses»)
3. Next, select on the left WAN
4.WAN Connection type: PPPoE
5.User Name: Your login from the contract
6.Password:Your password from the agreement
7. Set the point to Connect Automatically
8. Press the button “ Save».

Configuring PPtP (VPN) while automatically obtaining a local IP address (DHCP).

1. Select the menu on the left Network, further MAC Clone
2. Click Clone MAC address, further Save (for more details see in section "MAC Cloning addresses»)
3. Next, select on the left WAN
4.WAN Connection type: PPTP
5.Username: Your login from the contract
6.Password: Your password from the agreement
7.Server IP Address/Name: ppp.lan
8. Set the point to Connect Automatically
9. Save the settings with the “ Save»

Setting up PPtP (VPN) with a static local IP address.

1.WAN Connection type: PPTP
2.Username: Your login from the contract
3.Password: Your password from the agreement
4. Set the point to Static IP
5.Server IP Address/Name: ppp.lan
6.IP Address: We enter your IP address according to the agreement
7.Subnet Mask: We hammer in the mask according to the contract
8.Gateway: We drive in the gateway according to the contract
9.DNS: 212.1.224.6
10. Set the point to Connect Automatically
11. Save the settings with the “ Save».

NAT when automatically obtaining an IP address (DHCP).

1. Select the menu on the left Network, further MAC Clone
2. Click Clone MAC address, further Save (for more details see in section "MAC Cloning addresses»)
3. Next, select on the left WAN
4.WAN Connection type: Dynamic IP
5. Save the settings with the “ Save».

MAC address cloning (required when setting upPPPoE, PPTPwith dynamic settings andDHCP)

Saving/restoring router settings.

menu Backup & Restore.

To save the current router settings, you must press the button Backup. The settings file will be saved to the specified location on your hard drive.

To restore settings settings from a file, you must click the file selection button, specify the path to the settings file, then click the button Restore.

– favorites among devices that provide Wi-Fi. They are given the championship cup for their laconic design and wide range of actions. It won’t be difficult to find a model in the collection that matches its design and characteristics, but to understand the router settings, you’ll have to work a little.

To help beginners, the article offers brief instructions on how to connect a router to a PC and start using the Internet, which is not limited by wires. The guide consists of 5 stages of quick activation, upon completion of which you will be able to catch wi-fi anywhere in the apartment.

Determining the IP Address

The first step is to search network settings for authorization. There are only three types of them:

1. Dynamic (Dynamic IP);
2. Static (Static IP).
3. Access via PPPoE protocol.

And now about how to get them. For example, a user with Windows 10, to which the provider’s cable is connected. Internet is active. In this case, to find out the operator’s address, a person needs to go through the following route:

• At the beginning, click on “Start” - “Settings”;
• then look for the inscription “ Home page»;
• In the suggested options, activate the “Network Control Center”.

Now the “Change adapter parameter” field.

A column with the word “Internet” will appear on the screen. Click on “Properties”, and after that, in the list of “IP version 4 TCP/IPv4”, another click on the field of the same name.

The above maneuvers were carried out in order to find out the type of connection to the operator (see where the default icon is). If it is located in the “Obtain an IP address automatically” area, then synchronization is carried out through Dynamic IP. In this case, you can activate all the settings in an instant, without wasting time and effort. The process is carried out regardless of user actions.
When the “Use the following IP address” field is active in the window and numbers are indicated in the cells, this indicates the use of Static IP. In this case, the obtained data should be written down on a piece of paper, because they will be useful for subsequent actions with a router like.

Why was all this necessary? From this stage, the upcoming TP-Link WI-FI router settings will depend on the received IP address and differ in their set of procedures. But more on this later.

Installing and regulating device activity

It's time to connect your purchase to your laptop or use Wi-Fi. In the process you need:

• provider cable (by this time it should already provide Internet access to the house);
• patch cord (power cord);
• actually, a computer;
• router of the selected model.

At the next stage, these elements must be assembled into a single structure. There are several connectors on the back of the router. Most often there are 4-5 of them, and TP-Link painted these ports in different colors. It is important to remember that the blue Wan connector is used only for the Internet cable (there is only one), and the rest are used for synchronization with a PC.

You may be interested in the following information:

The connection process consists of 4 stages:

1. We remove the provider patch cord from the laptop.
2. We move it to the Wan connector.
3. We fix the selected router to the laptop with a power cord.
4. We connect the power supply of the device to an outlet.

All that's left to do is to configure the network reception correctly.

On the back of the router (for example), its basic data and factory settings are indicated. From this information, you need to select the site address and enter it into the search box of your browser. A window immediately opens with fields for login and password, which are specified in the documentation or on the same sticker.

After this, the user has access to tools for changing the functionality of the device. It's worth starting with local network. Select the “Quick Settings” section, in which you need to fill in all the fields: come up with a security password, name of the wireless network, determine the number of channels, signal reception time, etc.

Only after completing these steps can you proceed to activating free use of the Internet. To do this, open the “Network” and “WAN” tab. The first thing that appears at the top of the window is the connection type. This is the same IP address that has already been determined using the instructions in the previous section. Depending on it, the further process has three different options.

It is worth noting that the web interfaces of all TP-Link models are similar to each other (and this is no exception). It is not difficult to understand the key points. Here are the basic information you need to know to fill out each of them:

Dynamic IP – setting up a network automatically

If the operator provides the user with Internet communication services through a dynamic address, the entire activation process takes a matter of seconds.

To establish a connection you need:

• find the Dynamic IP item in the WAN list;
• save changes;
• go to System section Tools - Reboot;
• restart the device.

Now all the settings have taken effect and you can safely use the World Wide Web.

Static IP – we use the provider’s data

If the connection to the operator occurs using a static IP, first select in the WAN line the right option addresses. A window will appear on the screen where you need to enter your provider data. If they are already written out on a piece of paper in advance, then there should be no problems here. The information is registered - click on the “Save” field. Next, similar to the previous option, you need to restart the router.

PPPoE – remember login and password

Having selected this type of connection from the proposed menu, you need to fill in several data:

1. Subscriber name and password, which is specified in the agreement with the provider.
2. Operating mode, that is, determine accurate watch or around the clock.

After that, click the “Connect” button. In just a few seconds the device will be ready for use. You can make sure that the router is active at the bottom of the section. There should be the word "Connected".

Router security: quick setup

In order not to distribute free Wi-Fi to all your neighbors, it is better to immediately protect it. The most secure encoding is WPA-PSK/WP2-PSK.

Activating it is very simple:

• section “Access Control” or “Security Setting”;
• mark next to the column with the desired name.

A prerequisite for a secure line is the presence of a cipher. You need to invent it, add it to the line and, preferably, remember or write it down. The cipher must contain at least 8 characters. It is better to use Latin letters mixed with numbers. When finished, be sure to restart the router. This way, all changes made will remain in the system.

Internet connection to the device

The final part of setting up a TP-Link router is to enable the laptop to receive a signal from the router. On the bar at the bottom of the screen, you need to find and select the network activation icon by clicking the model name from the proposed list. To activate it, you need to enter the password you created earlier. Now left-click on the “Enable” or “Save” button. To test the operation of the device, go online to any of the sites.

After that, you can synchronize any devices that support the Internet with Wi-Fi: set-top box, other gadgets.

How to recover a lost password?

It happens that after some time the password to access the router settings is forgotten. If this happens, it doesn't matter.

There are several solutions to the problem:

1. You can restore all original settings using the Reset button on the device panel.
2. Log into the web service from any connected device and see your forgotten password.
3. Try standard login details admin/admin. Perhaps they haven't changed.

If you choose the first option, you will have to go through all the installation steps again

Brief summary

At the end of the instructions TP-Link connections router, all that remains is to consider a few mistakes that beginners make when connecting a device:

• before starting the activation process, the Wi-Fi button located on the back of the case was not pressed;
• the username matches the name of the router model, which is why it is lost in the list;
• operator parameters are incorrectly specified;
• The wrong connector is selected for connecting the patch cord.

Everything is simple, nothing fancy. If you look closely, connecting a TP-Link router will take no more than 5-7 minutes. It is important to take your time and follow the instructions carefully.

Hi all! Nowadays Wi-Fi router Most users install it at home. Firstly, it is extremely convenient, unless you are a fan of getting tangled in wires and being tied to one place. Secondly, with the purchase of mobile gadgets, the need arises to have unlimited high-speed Internet at home. Otherwise, you will have to run to a cafe with Wi-Fi every time to download the game to your phone. And this is not serious at all, is it?

Why all this fuss around routers? Few people know how to configure a Wi-Fi router so that the connection is stable, powerful and fast. Using the TP-Link router model TL-WR841N as an example, we will tell you how to set up a tp-link router at home without calling a specialist.

A few words about the model we will be working with today. Without a doubt, this is one of the best offers on the router market, which at one time was purchased for 1,200 rubles. The router is relatively inexpensive, but can provide you with full-fledged Wi-Fi connection throughout the apartment.

How to connect a router model TP-Link TL-WR841N?

1. So, you have become the happy owner of a router and brought it home to celebrate. Opening the box, you will see inside a lot of different pieces of paper, a disk with instructions in electronic form, as well as the router itself, a small power supply for it, and a network cable for connecting to a home PC.
2. The question of how to configure a tp-link router does not concern us yet. First you need to connect this device, everything else comes later. Place the router close to the computer in a convenient place on a stable surface. In principle, it can be placed in the hallway, and even in the kitchen - as long as there is enough wire. Since the included network cable is usually not very long, place the transmitter near the PC or go to a computer store, where they will crimp a longer cable for you.
3. Connect power to the router and plug it into a power outlet. Then connect the Internet cable to the WAN socket (it is blue). Please note that there are four LAN ports. Therefore, it will be possible to connect via network cable four PCs at once (if necessary). We connect the computer to the router using the cable that came with the kit.
4. To make it clear to you, let’s briefly go through all the connectors and buttons of our router (picture below):

1) This button can be used to turn the router on and off.

2) Power cord.

3) WAN connector required to connect to the Internet.

4) LAN connector, through which we connected the router to the computer.

5) Enabling the QSS option.

6) Emergency button (too bad it’s not red). Resets all router settings.

How to set up a Wi-Fi router quickly?

How to properly configure the Internet on a router?

How to set up a full Wi-Fi network on a TP-Link TL-WR841N device?

That's all! We have just set up the Wi-Fi router and saved the money needed to call a specialist. How good it is to do something, realizing that you are doing it yourself, that you have learned how to do it! If you have any questions along the way, don’t hesitate to ask them in the comments below. Good luck to everyone, until new publications!

The TP-Link TL-WR841N router is one of the most popular router models that has proven itself from the very the best side and, as a result, is in consistently high demand among many users. In this article, we will consider in detail the procedure for connecting and setting up a router, including a detailed description of configuration wireless wifi networks.

Brief specifications of TP-Link TL-WR841N

How to connect a router

The router package includes:

• Router TL-WR841N;
• Power adapter;
• Ethernet cable with RJ-45 connectors;
• CD for quick setup;
• Management.

We unpack the box and proceed to installing and connecting the router. First, connect the device to power using the adapter and click on Power button on the rear panel (if the indicators on the router light up on their own after power is applied, then you do not need to press the button).

Next, use the included Ethernet cable to connect the router and computer. We plug one end of the cable into one of the four yellow LAN ports of the router, and the other into the connector network card PC. Then we connect the cable coming from the Internet provider or ADSL modem to the blue WAN connector of the router.

In principle, that’s all, now you can proceed directly to setting up the router, but first let’s make a reservation that along with it comes a CD with a utility that allows you to quick setup router in step-by-step mode. We will not consider this method, because the configuration option via the web interface is more preferable.

Basic setup of the TP-Link TL-WR841N router

Since the router will now be responsible for connecting to the Internet and distributing it, there is no need for the high-speed connection created earlier in Windows. At the same time, the connection via the local network connecting your computer and router needs to be configured. Let's go to Control Panel - Network and Sharing Center shared access– Changing adapter settings. Click right click mouse over the active connection and select “Properties”.

On the “Network” tab, set the switches to “Obtain an IP address automatically” and “Obtain a DNS server address automatically.”

Also in position automatic settings We put a switch on the “Alternative configuration” tab. Save the changes with the “OK” button.

Now we launch any browser and in address bar we register http://tplinklogin.net/ or 192.168.0.1 . Then in the window that opens, enter the username and password - by default this is admin And admin.

The standard username and password are indicated on the label on the bottom of the router. Look at it and make sure once again that all login information for the TP-Link TL-WR841N configuration web interface has been entered correctly.

If everything is done correctly, you will be taken to the administration panel. Here we immediately go to the Internet settings.

Internet setup (WAN)

Select “Network” from the menu on the left (in the English interface – Network), and then the WAN section. In the “WAN Connection Type” drop-down list, select desired type connection to the provider.

The following options exist:

• Dynamic IP address;
• Static IP address;
• PPPoE;
• L2TP;
• PPTP.

There is no point in delving into the essence of all these types of connections. Information on which one to choose is provided by the provider. The Internet service provider also transfers authorization data to the client - username and password. If you suddenly forgot this data, you can look it up in the contract. The second option is to call the provider's support service.

So, let's set it up WAN connection according to the following schemes:

• When choosing dynamic IP address no additional actions are required;
• Option Static IP address requires entering the IP address, subnet mask, gateway and DNS. We remind you that all this data is provided by the service provider, i.e. your provider.
• Connection type PPPoE requires entering a username and password.
• When selecting a connection L2TP indicate the username, password and IP address/VPN server name.
• Connection type PPTP will also require you to enter your username, password and IP address/VPN server name.

After all the data has been entered, click the “Save” button. The Internet should work.

After setting up the Wi-Fi router TP-Link TL-WR841N there is no Internet access

If you have configured everything exactly according to the instructions, but as a result the Internet does not work, you need to do the following:

If none of the above steps help, the router may be faulty. To make sure the device is working, try connecting it to your friends or acquaintances.

Wi-Fi setup

Providing opportunity wireless connection connection to the Internet is one of the most important functions of a router. Let's move on to the Wi-Fi settings for TP-Link TL-WR841N.

Go to the section Wireless Mode - Settings wireless mode (Wireless – Wireless Settings). Set the name of our Wi-Fi network and select the region.

Below are network settings that may affect signal quality and coverage in certain situations. We will not focus on them, since this is a topic for a separate large conversation. Leave all settings at their default values ​​and save your settings.

Now we need to protect our wireless network from unauthorized connections of third-party users. Select “Wireless Security” on the left.

Set the switch to the “WPA/WPA2 - Personal (recommended)” position. Next, select the version, encryption type and set a password. We save the changes made.

Setting a new administrator password

Standard username and password for accessing administrative settings make your TP-Link router TL-WR841N is very vulnerable, so it is better to change them immediately. Let's move along the path System Tools - Password (System Tools - Password). Here we enter the old and new data for authorization (you can only change the password, but leave the user name as admin), and then click “Save”.

You can write down your password somewhere so you don’t forget it.

Perhaps this is it basic setup Wi-Fi router TP-Link TL-WR841N is completed. Of course, there are still a lot of different functions that can be useful to users. However, this will be a more subtle configuration that requires a separate article. We achieved the main goal - we set up the Internet and Wi-Fi.

For all settings to take effect, reboot the router. This can be done programmatically through the section ( System Tools - Reboot) or physically by turning off the power. After loading it should appear Wi-Fi network with a given name, to connect to which you will need to enter a password. The Internet must work in both wired and wireless mode.

Currently unlimited high speed internet– this is no longer a novelty. And even more so if we are talking about a wireless connection option, which is applicable even for a personal computer, not to mention laptops, tablets or smartphones. Now the majority mobile devices has a built-in WiFi module, and their comfortable use directly depends on how high-quality the wireless connection is installed in your home and how well you can connect everything to the computer.

WiFi routers TP-Link is good example solving problems with speed, range and antenna power. You are also guaranteed to get rid of wires in your apartment. After you have purchased a router, it is very important to understand how to properly connect the device to your computer yourself. The fact is that if you already have the Internet, then the lack of knowledge on this issue can lead to additional costs for calling specialists.

In this article we will try to tell you how to properly connect your TP-Link to a computer and configure it subsequently.

Connecting to a computer

The first thing you need to do is open the box and make sure that the configuration of the TP-Link router matches what was described in the documentation. That is, make sure that all the elements are in place. In addition to the router itself, you must have a power supply, cables, and a disk with software.

Before you connect your TP-Link router to your computer, you need to place it correctly. It's best to place the cable close to where your PC is, as the included cable isn't very long. If this fails, then you can purchase more long cable additionally. It is very cheap and can be found in any electronics store.

The TP-Link router has the following buttons and connectors, most of which we will need when connecting and setting up:

• power button;
• WAN connector for connecting the router to the Internet;
• LAN connectors for connecting a PC using a network cable;
• disabling and enabling the QSS function;
• button to reset the router settings.

After you have become familiar with the location of the connectors, you need to connect the power supply to the TP-Link router and plug the unit into a power outlet. A cable that was laid by the provider is connected to the WAN socket located on the device body, that is, connecting directly to the Internet. The TP-Link configuration assumes at least four LAN ports, so you can connect four at once personal computers if you use a network cable.

Setting up a TP-Link router

Before you start setting up, experts recommend performing a preliminary reset to factory settings. After the router has rebooted, use any browser. In the address bar, enter 192.168.0.1. Another option is 192.168.1.1, depending on the firmware version. You will automatically gain access to the Setup Wizard.

To get inside, enter your password and login. By default, both lines are admin. For further network security, it is better to change your password during preset, which is discussed in at the moment. To change the input data, go to the System Tools tab, where you need to click on Password. In the Old User Name and Old Password fields you will need to enter the factory login and password, that is, admin. Create a username and password. In principle, you can leave the old login. Enter new data in the New User Name, New Password, Confirm New Password fields. The last field is confirmation of the new password. Don't forget to save your updates by clicking Save.

On the setup page, you can optionally download and install immediately latest version firmware. The installation itself is carried out through the System Tools menu, where you need to go to the Firmware Upgrade field. In it you should click on Browse, select the downloaded file and click on Upgrade. Downloading must be done only from official TP-Link resources. Fully licensed firmware is provided absolutely free.

Setting up the Internet in a TP-Link router occurs in the Network and WAN menu. The first thing you need to do is select your network type. If he is unknown to you, then simply clarify him by calling “ Hotline» provider. After you have chosen the type, you will need to save the settings, for which you need to click on Save.

After successful saving, go to the next tab labeled MAC Clone. There is a Clone MAC Address button, which you need to click on, and then save everything using Save.

How to set up a WiFi network on a tp link router

To set up a wireless connection, you need to go to the Wireless tab. There is a field here labeled Wireless Network Name. The name of your network is entered into it, and it can be chosen arbitrarily. If desired, you can enter the name of the country in the field below. Don't forget to save all changes.

On the Wireless Security tab, you configure the security system configuration, including protection against unauthorized access. To do this, you need to come up with a not too simple password and enter it in the PSK Password column.

All changes to the settings must be saved, after which the router must be rebooted. You need to reboot the device from the Reboot button located on the System Tools tab. After clicking the button, you just need to confirm your action.

Conclusion

As you can see, there is nothing difficult about connecting and configuring the router yourself. It's really simple and doesn't take much time. And you can save money on calling specialists and the time during which you would have to wait for them.