How to disassemble iPhone 5. Complete disassembly of iPhone. What is needed for analysis

The moment has come. The time has come. The day has come. Choose the most successful introduction for an article about how gradually, screw by screw, loop by loop, it turned into a neatly folded pile of spare parts. iFixit We went to Australia again to be one of the first to buy a new product and immediately disassemble it. This is their most important gallery in the last two years. And the most interesting.

The slots of the two screws on the bottom end are still Pentalobe, but the threads are a little different. Once the screws are removed, you take the suction cup and remove the display just like you would a 3GS. iPhone 5 is being disassembled again front, and not behind, like . Thanks to this, replacing the display has become much easier, and there are already rumors that Apple Store ending the policy of replacing the entire phone with a refurbished model.

The display connector is screwed to motherboard with regular Phillips screws. What a kind Apple.

That’s all, to remove the display, all you have to do is carefully pick up the connector with a tool with a flat tip.

iPhone 5 inside, please love, favor and stand in line at the Apple Store.

The operation with the connector must be repeated for the battery. All the screws here are still Phillips.

The battery is glued to the back, but unlike , glue is not a problem here. You slip something in and carefully peel the battery off the bottom.

Done, battery removed. The display from the iPhone 5 is as easy to remove as from the 3G and 3GS, and the battery is no more difficult than from the 4 and 4S. Golden mean.

The battery is manufactured by Sony at its plant in Singapore. Energy characteristics - 5.45 watt-hours, voltage - 3.8 volts, capacity - 1440 milliamp-hours. All three figures have increased slightly compared to the 4S (5.3 Wh, 3.7 V, 1432 mAh).

The next step is the motherboard. A wire from one of the antennas runs from it over the block with the Lightning connector, but it can be easily pulled out with the same universal tool.

Inside the iPhone 5 there are a great many purely contact connections, when metal is adjacent to metal. These connections make repairs easier, but you need to make sure your hands are clean. The result of any slightest dirt getting between the contacts may cause the device to malfunction.

Since the body also consists entirely of antennas, some connectors are connected directly to it.

Freedom for motherboards!

And the cameras too. This is the main sensor, 8 megapixel. We will return to him later.

Bottom of the board:
Red - GSM/GPRS/EDGE signal power amplifier, Skyworks 77352-15;
Orange - module for switching between antennas SWUA 147 228;
Yellow - UMTS signal power amplifier, also known as duplexer, Triquint 666083-1229;
Green - Avago AFEM-7813 dual-band LTE duplexer;
Blue - CDMA signal power amplifier, Skyworks 77491-158;
Purple - LTE signal power amplifier, Avago A5613 ACPM-5613;

Red - Qualcomm PM8018 RF power controller;
Orange - Apple 338S1131 power controller, manufactured by Dialog;
Yellow - 16 GB Hynix H2JTDG2MBR flash memory chip;
Green - multi-chip auxiliary memory module for LTE, Apple 338S1117, manufactured by Elpida;
Blue - STMicroelectronics L3G4200D three-axis gyroscope, as in the iPhone 4S and iPad 2;
Purple - Wi-Fi module Murata 339S0171.

The most curious thing is hidden under another thin metal plate...

The A6 chip is the first Apple chip with a custom core design based on the ARMv7 microarchitecture (read the history of its creation). The markings on the right indicate a 1GB module random access memory by Elpida Memory. It seems that two RAM manufacturers are once again working for the benefit of Apple - Elpida and.

iFixit explains how the Apple 338S1077 hardware audio codec from Cirrus works. The codec serves as an audio converter from analog signal to digital and vice versa. This way the sound is decoded into input and output.

Top part fees:
Red - triaxial accelerometer STMicroelectronics LIS331DLH with low power consumption;
Orange - single-chip controller touchpad Texas Instruments 27C245I;
Yellow - another touchpad controller, Broadcom BCM5976;
Green - Apple A6 chip;
Blue - the vaunted Qualcomm MDM9615M LTE modem for transmitting both voice and data;
Purple - RTR8600 multi-band transceiver, as in... Galaxy S III.

The second touchpad controller (the iPad also has two), Broadcom BCM5976 - exactly the same as in MacBook Air, only there it functions as a trackpad controller.

A cable with a Lightning connector glued to the case is not even a cable, but a whole massive block. In addition to the connector itself, it contains: mini-jack, main speaker, dual-band (2.4 GHz and 5 GHz) wifi antenna and one of three microphones.

Here, by the way, is the microphone itself.

They finally came face to face, 30-pin connector and Lightning. The forces are not equal.

Look, they weren't lying, Lightning actually has eight pins. The new connector is “fully digital”, so for the notorious cable you will have to equip it with a converter made of digital signal to analog. Such a cable will not be cheap...

The plug is held inside the connector using side clamps...

...as well as the contacts themselves! Both the latches and the contacts are spring-loaded, so the plug can only be removed with some force.

iPhone 5 is incredibly light. The rather empty metal case weighs not much more than the glass panel from the iPhone 4S alone. Don't ask about scales.

Before us is a vibration motor, made by analogy with... the GSM version of the iPhone 4. The CDMA version, as well as the 4S, had a so-called linear oscillating motor, more perfect than this.

The design of the Home button now includes a support bracket, which should extend its service life. I would like to believe that from now on it will not be necessary.

Behind the display lies a metal plate covering its entire area. The plate performs many functions: shielding, heat dissipation, and perhaps even grounding.

This is what people (including -) are talking about so much now. The problem of paint peeling has already been dubbed “scaffgate” (from the English “scuff” - “scuff”), by analogy with “” 2010. iFixit says the beveled edges are actually very easy to scratch. Clickable photo:

Clickable

On the left is the 8-megapixel camera from the iPhone 5, on the right is the same one from the 4S. Apple was not lying about the reduced size of the module, and we were not lying about the improved image quality.

Scratching a sapphire eye is not an easy task. iFixit didn't succeed.

Finally, let's take a look at the two noise-cancelling microphones. First - on the one in front, next to the front camera.

Then - to the one on the back, between the main camera eye and the flash.

Before moving on to the results, let’s look at the video with Melissa Godsey, which the smart iFixit have already managed to edit.

Because of all its collapsible advantages, the iPhone 5 gets seven points out of ten on the maintainability scale. There could be more if Apple hadn't concentrated so many elements on one block with the Lightning connector - you can't replace them separately. Still, this is an improvement over the 4S's six points.

Clickable ( 5.00 out of 5, rated: 1 )

Tools for DIY iPhone disassembly

In order to repair an iPhone 5 and disassemble it, you will need special tools. So, stock up on: a Pentalob screwdriver, a suction cup for the screen, a small Phillips screwdriver, a small spatula.

Instructions for disassembling iPhone 5 yourself

First of all, you should turn off the device, then you need to unscrew all existing external screws using a Pentalob screwdriver.

Then we take the suction cup in our hands and carefully lift the smartphone screen. If necessary, you can use something thin to pry up the screen, but be careful not to scratch the device.

At this stage we must remove the screws as well as the fastenings.

Connectors, cables, and antennas should be disconnected. Remember that when working with cables, you need to use a spatula, it is better if it is made of plastic.

Remove the display.

Unscrew the cable protection, which is located in the center of the motherboard.

Don't forget to disconnect the battery. In this model, this cannot be done immediately, so it is turned off at this stage. We take out the battery, which needs to be pryed off with a spatula.

So, we gradually reach the motherboard. Unscrew the 2 screws that hold the camera.

Then you should disconnect the microphone and speaker cable. Don't forget about the headphone output cable.

After this, you need to disconnect the antenna cable and remove our SIM card tray.

We disconnect all the cables that hold the back panel and the board together.

Using careful movements, remove the motherboard. To do this, remove the cables and 5 screws.

We unscrew 2 screws from protecting the iPhone camera. The camera is freely detachable from the motherboard.

Then, remove the 3 screws that hold the vibration and disconnect it.

Then you should unscrew 2 screws located next to the headphone jack and one on the right side of the lower cable.

The final stage is to remove the 4 screws of the lower cable and take it out.

We are often asked: “Is it difficult to disassemble the fifth iPhone?” The answer is no. But there are several nuances. In order to disassemble the iPhone 5 with your own hands, you will need a special 5-point screwdriver, a suction cup, a pick and a plastic spatula. If this is your first time dealing with phone disassembly, you will need maximum perseverance, attentiveness and caution.

1. At the bottom of the phone, next to the system connector, you need to unscrew two bolts.

2. Using a suction cup (at the bottom, closer to the Home button), we remove the display module from the case, prying it with a plastic spatula or a pick.

3. After lifting the display, you need to unscrew the bolts securing the plate that presses the display connectors to the board. Next, remove it to the side.

4. After the display cables become accessible, carefully pry them up with a spatula and disconnect them.

5. This leaves us with the display module and the back of the case with all the assembled components in our hands.

6. The next step in disassembly is to move on to the battery iPhone battery 5. Unscrew the fixing plate and disconnect the battery connector. The iPhone battery is glued to the body along its entire perimeter. In order to remove it, you need to pull the plastic tab sticking out from under it and pry it off with a spatula.

7. In the same way, disconnect the system connector cable and coaxial cable antennas. Their connectors are located next to the battery connector. Next, unscrew the frame securing the main camera and flash LEDs.

8. Unscrewing the bolts in the upper inner part of the body and around the perimeter motherboard, You can thereby remove it from back cover. When disassembling the iPhone 5, do not forget to disconnect the coaxial cable of the antenna under the board!

9. Having removed the main board of the iPhone 5, we can say that the iPhone is practically disassembled.

10. To replace the system connector cable and polyphonic speaker, you need to unscrew the fixing bolts and, using a spatula, remove them from the case.

11. Let's move on to the display module of the iPhone 5; disassembling it yourself is not difficult. Several elements are recorded on it. This is a voice speaker.

12. The front camera on the cable is fixed with a common plate. Be extremely careful when peeling off the light sensor and camera cable!

13. It won't be difficult at all to remove Home button. Sometimes liquid or dirt can cause it to fail. correct operation. In such cases, either cleaning or complete replacement is required.

14. When disassembling the iPhone 5, be sure to remember where this or that element was located, because after disassembling it still needs to be reassembled correctly. If it scares you Repair iPhone 5 with your own hands, contact service center Tech-Profi.

For several days in a row you can buy iPhone 5. Some happy smartphone owners run home to rejoice at their purchase, others go to their homeland to sell their treasured smartphone at three prices. Here are the guys from the team iFixit Traditionally, they go to their laboratory to disassemble the creation of hundreds of company people Apple.

At first glance it may seem that this is not difficult to do, but we still We do not recommend doing this, unless you have special skills, education or a strong need. After all, you can take it apart, but it will be more difficult to assemble it.

If you still decide to disassemble the iPhone 5, you will need:

• Sucker
• Spudger (plastic tool)
• A special Phillips screwdriver that can be purchased from iFixit.com or ordered from Ebay.

On the bottom panel we find two bolts, which we quickly unscrew with a Phillips screwdriver.

The connector is screwed to the motherboard. Again we resort to using a Phillips screwdriver.

Then we use a tool with the simple name Spudger; of course, you can use something of your own that is similar in properties. Completely disconnect the display from the motherboard and...

...We get two such beautiful pieces.

After a few moments we get a battery at the output. Manufacturer: Sony. Compared to iPhone 4S, new battery somewhat more powerful.

Next we will work on motherboard. Carefully unscrew all the bolts and pull out one of the wires. Before you begin disconnecting the contacts, make sure your hands are clean. iFixit warns that dirt inside the case may cause problems with your device in the future.

Several bolts hold the motherboard and antennas to the case. Crosshead screwdriver!

Carefully remove the board from the case.

Almost all components on the motherboard are bolted together. Using a screwdriver, remove the camera module.

The next step is the path to the heart of the device - the A6 processor. It is hidden under a small film that can be easily torn off.

The processor itself. This copy was made by Elpida Memory. It looks like Apple is gradually getting rid of its only partner in this area. We're talking, of course, about Samsung.

Then we take on the Lightning port, which must be removed along with the headset jack, speaker, Wi-Fi antenna and one of the microphones.

And here is the entire structure separately from the body.

And here is the answer to the question why Apple installed a new connector instead of the old one: evaluate the difference in size (the new one is located lower).

To prevent the Lightning connector from flying out of the port, Apple came up with these clever holders.

The case and screen look like this.

While disassembling the iPhone 5, one problem was discovered. It turns out that the side edges can be scratched, during which the true color of the metal appears - silver. Getting gray stripes on a black background is never fun. Let's hope that this is just an isolated defect or a defect in the first batches. On this moment Quite a lot of people have already complained about such a shortcoming, but I want to believe that Apple can fix everything.

Ready!

After disassembling the iPhone 5, the guys from iFixit summed up a small conclusion - fixing the iPhone 5 is not very difficult - the smartphone received 7 points out of 10(10 points - very easy to repair). Last year The iPhone 4S received a 6 rating. By the way, MacBook Pro with Retina received only 1 point. According to the report, Apple did the right thing by getting rid of glass, as it was quite fragile.

Owners of iPhone 5 and 5S are wondering how to disassemble the phone. Time is not kind to even the best devices: the panel can become frayed (especially on black models), the sensor fails, and those who like to “swim” have problems with the hardware. To replace iPhone parts you need to know internal organization and be able to disassemble the device.

What do we need?

Before you start disassembling, set aside enough time for this and stock up on all the necessary tools. This iPhone disassembly kit can be purchased at any specialized online store:

• Pentalob five-blade screwdriver (without it, the bolts are unlikely to yield to you);
• Phillips screwdriver;
• vacuum suction cup;
• plastic spatula for disassembling the case (or something similar).

Step-by-step instruction

1. The first thing we need to do is unscrew the two screws at the bottom of the case, on the sides of the Lightning connector. The iPhone 4 used Phillips screws, more later versions To prevent self-disassembly of phones, Apple developers began to use special five-lobed Pentalob bolts.

If you don't have a special screwdriver for them, you can try using a five-pointed star or take a flat one and sharpen it with a file on the sides. But be careful, if you use non-standard means you can grind off the bolt heads. Just in case, it is better to stock up on bolts of the same size, but with a cross-shaped head.

2. Using a vacuum suction cup, slightly lift the screen, helping yourself with a plastic spatula. Why a spatula and not a screwdriver? Thus, we reduce the likelihood of damage to the iPhone case or screen. This can be done without the help of a suction cup, by hooking something (some use a needle) on the top panel, but extreme caution must be used.

3. Carefully lift the screen from the side of the “Home” button. At this step, the first differences between the 5 and 5S models appear. On the iPhone 5, the front panel simply rises to form an almost right angle with the body.

On the iPhone 5S the situation is more complicated. The screen is attached to the motherboard with a cable, so do not lift it suddenly. You need to disconnect the cable before further work using a plastic spatula. And after that, raise the screen, as in version 5.

4. To finally disconnect the screen, use a Phillips screwdriver to remove the two screws that hold it in place.

Then carefully pick it up with a spatula.

The iPhone is divided into two parts, each of which can be disassembled into several more components.

5. Let's pay attention to the display panel. Unscrew the “Home” button. It is the same in both models.

6. At the top of the front panel, the 5 and 5S models again have differences. The 5S has a camera, a proximity sensor and a speaker, which are removed after removing the mounting plate.

U 5 iPhone versions The mount has an auditory speaker, which is held on by two screws and spring contacts. Front camera You can simply remove it if necessary, it is held on by a cable.

7. Last action with the front panel - getting rid of metal protection.

8. Let's move on to the device body. The first step is to get rid of the battery so as not to get an electric shock. We disconnect the cable from the board with a plastic spatula.

Using the same tool, we pry up the battery and pull the label (it is missing in the 5S, so we only use a spatula). If the battery does not budge the first time, there is no need to be alarmed, it is glued. The glue is not too strong, so the battery will give in easily with a little more effort.

9. Disconnect the main camera in version 5. It is held on by two screws; after removing them, the chamber is free. In 5S it is in this state initially.

10. The next step is to remove the motherboard. There is no difference between the iPhone 5 and 5S. Disconnect the antenna connector module from the motherboard. Unscrew the screws securing the board to the case and the contacts on the inner wall. Carefully remove the motherboard.

11. There is a processor on the motherboard: A6 for 5 and A7 for 5S. When disassembling for the first time, you will need to remove the protective film.

12. Let's continue disassembling the case. At its bottom there is a headphone jack, an earpiece, a Wi-Fi antenna (for version 5) and a bottom microphone - all of this is attached to the Lightning connector. We get rid of the mass of glue with a plastic spatula.

Remaining parts on the top of the case

14. As a result, we get a disassembled phone. You can reassemble your device by following the same instructions in reverse order.

Version 5S looks like this:

Possible mistakes

• You are entirely responsible for assembling and disassembling the device. If you doubt that you will succeed, take it to the service center - the specialists will help.
• When disassembling the device yourself, remember the warranty period. Once you open the case yourself, the warranty is automatically void; subsequent repairs will be at your expense.
• Don't skimp on special tools: they will cost less than repairing or buying a new phone.
• Do not make any sudden movements; with your careless actions you can tear off the cable or break particularly fragile parts of the iPhone.

Video: iPhone 5 disassembly

Video: how to disassemble iPhone 5S

At creating an iPhone 5 and 5S Apple made sure that they could not be easily disassembled. This process will take a long time, but it can be done by an ordinary person. If you are confident in yourself, you can try to disassemble the iPhone at home yourself, otherwise, take the device to a competent technician, he will know exactly what needs to be done.